Commercial Flagpole Installation in Alabama
Factory-direct poles from FlagCo. Local installation from Alabama Flag & Banner.
Need a commercial flagpole installed in Birmingham, Huntsville, Montgomery or Mobile? FlagCo manufactures the pole at our factory in Acworth, Georgia. Alabama Flag & Banner, who have been sewing flags in Huntsville since 1985, install statewide. One quote, one point of contact.
Authorized FlagCo Dealer & Installer
Huntsville, AL • Sewing American flags since 1985. Alabama Flag & Banner has made flags in Huntsville for four decades, cutting the fields, slitting the stripes and hemming every flag in their own shop under president Belinda Melson-Kennedy. They also sell and install commercial aluminum flagpoles from 20 to 80 ft, for businesses, schools, churches and government sites across Alabama. As an authorized FlagCo dealer, they order FlagCo-manufactured poles factory-direct, with no separate distributor in between. Visit alabamaflag.com.
Two American Manufacturers, One Installed Project
Most flagpole companies resell somebody else's pole and buy their flags from an importer. This is the opposite of that. Alabama Flag & Banner has sewn American flags in their Huntsville shop since 1985, cutting the blue fields, slitting the stripes, hemming and joining every piece. FlagCo builds the pole in Acworth, Georgia.
So on an Alabama project you get the flag from the people who sewed it and the pole from the people who machined it, set by the same crew. They install statewide, from Birmingham office parks to Gulf Coast sites, in commercial aluminum from 20 to 80 ft, external halyard or internal, with the hardware to match.
They handle the outliers too. In November 2025 they set a 5,000 lb steel pole on eight tons of concrete overlooking Lake Guntersville, flying a 30 by 60 ft flag they sewed in the Huntsville shop (covered by the Sand Mountain Reporter). That one was steel and well past the 80 ft FlagCo manufactures. Most days the work is a 25 ft pole outside an office, and it gets the same rigging and the same foundation math.
Our side starts in Acworth, Georgia, a couple of hours from Birmingham, where FlagCo cuts, machines and finishes 6063-T6 aluminum shafts per ASTM B 221, rated per NAAMM FP 1001-07 and backed by a limited lifetime warranty on the shaft. Their crew, our pole, one point of contact.
Want to know what an installation actually involves before you request a quote? Read our flagpole installation guide, then come back for the Alabama specifics.
Alabama Wind Zones Run from 90 to 120 MPH
FlagCo's wind speed data (ASCE 7-10, 3-second gust at 33 ft above ground) puts most of Alabama in a 90 mph zone. The southern third of the state, Dothan included, typically needs a 100 mph rated pole per NAAMM FP 1001-07, and coastal Mobile and Baldwin County sites need 110 to 120. Look up your exact address for a precise number.
Look up your exact address on FlagCo's Wind Speed Tool.
Your Pole Is Manufactured, Not Imported
Every FlagCo commercial flagpole starts as 6063-T6 aluminum stock, cut, machined and finished at our own facility at 3600 Cantrell Industrial Ct, Acworth, GA. Hardware, cleats and halyard systems are built in-house too.
Alabama Flag & Banner orders the pole direct from that factory. No importer, no separate distributor between the mill and your site in Alabama.
Why FlagCo and Alabama Flag & Banner
A flagpole install usually means coordinating a manufacturer and a separate local contractor yourself. This partnership skips that step.
Factory-Direct Pole
Manufactured at FlagCo's Acworth, Georgia facility: 6063-T6 aluminum shaft, NAAMM FP 1001-07 rated. Alabama Flag & Banner orders it direct as an authorized dealer.
Local Alabama Installation
Alabama Flag & Banner sells and installs flags, banners and flagpoles from their Huntsville shop, an authorized FlagCo dealer working sites across Alabama.
One Point of Contact
One quote covers the pole and the install. You are not coordinating between a manufacturer and a separate installer, or tracking two invoices.
Quote. One Crew.
One Warranty Call.
Five Steps From Quote to Flag in the Air
The same process whether it's a 20 ft pole outside a small office or an 80 ft pole at a corporate campus.
-
1
Tell them about your project
Call or send the form with your pole height, location and timeline. Most poles can be quoted with installation from those details; Alabama Flag & Banner walks the site first when the project calls for it.
-
2
Wind and code check
Alabama's wind zones run 90 to 120 mph under ASCE 7-10 depending on where you are. Alabama Flag & Banner confirms the exact requirement for your address before the pole is ordered, and handles the permitting your municipality requires.
-
3
Foundation work
Concrete foundation and steel ground sleeve, sized to the pole height. Set depth runs from 2 ft on a 20 ft pole up to 5 ft on a 50 ft pole.
-
4
Pole erection and rigging
The FlagCo shaft goes in, halyard and hardware get rigged, and the spun aluminum flash collar goes on at grade.
-
5
Lighting and final walkthrough
If you added a flagpole beacon, it gets mounted and wired on site. Alabama Flag & Banner walks you through the finished install before they leave.
Common Questions
What business owners and facility managers ask before installing a commercial flagpole in Alabama.
How much does a commercial flagpole cost installed in Alabama?
Installed cost depends on pole height, foundation and site conditions (concrete, asphalt, turf or a slope), whether you're adding lighting, and site access for the crew and equipment. There's no single number that fits every site, but most poles can be quoted with installation from the details you provide; Alabama Flag & Banner walks the property first when the site calls for it, and either way you get a firm install quote rather than a rough guess. Request an install quote to get a real number for your site.
Do I need a permit to install a flagpole in Birmingham, Huntsville or Montgomery?
Permit requirements vary by city and county across Alabama. Some municipalities treat a commercial flagpole like any other structure and want a permit and a footing inspection; others do not. Alabama Flag & Banner handles permitting as part of the install and will tell you what your municipality requires before work starts.
What wind rating do I need for a flagpole in Alabama?
FlagCo's ASCE 7-10 data puts most of Alabama, including Birmingham, Huntsville, Montgomery, Tuscaloosa, Auburn, Decatur and Florence, at a 90 mph wind zone. The southern third of the state, including Dothan, typically needs a 100 mph rated pole. Coastal sites in Mobile and Baldwin County, including Daphne, Fairhope, Foley, Gulf Shores and Orange Beach, run roughly 110 to 115 mph and need a 120 mph rated pole per NAAMM FP 1001-07, with a 110 mph band just inland of them. Look up your exact address on FlagCo's Wind Speed Tool to confirm.
Who actually installs the pole, FlagCo or Alabama Flag & Banner?
FlagCo manufactures the pole at our factory in Acworth, Georgia. Alabama Flag & Banner, a Huntsville flag and flagpole company and authorized FlagCo dealer, handles the foundation work and erection, with a site walk first when the project needs it. One quote covers both the pole and the install.
What flagpole heights and types are available?
FlagCo manufactures commercial flagpoles from 15 to 80 ft: external halyard, internal winch, internal cam cleat and reinforced configurations, rated from 85 to 170 mph per NAAMM FP 1001-07. Alabama Flag & Banner's commercial aluminum line runs 20 to 80 ft, and they carry residential options below that. They will help you match the type and height to your building and budget.
Can the flagpole be lit at night?
Yes. FlagCo makes flagpole beacons, lights that mount at the top of the pole and illuminate the flag after dark. The beacon ships with the pole order and is mounted on site during installation. Ask about beacon options when you request your quote.
What areas does Alabama Flag & Banner serve, and how long does installation take?
Alabama Flag & Banner is based in Huntsville and installs statewide, including Birmingham, Montgomery, Tuscaloosa, Decatur, Florence, Dothan and the Mobile area. Installation timeline depends on pole height, foundation work and permitting in your municipality; you'll get a project timeline with your quote.
Look Up Your Specs Before You Call
FlagCo's free tools cover the technical side; Alabama Flag & Banner handles the Alabama side.
Wind Speed Tool
Look up the ASCE 7-10 wind speed and NAAMM FP 1001-07 flagpole rating for your exact address.
Commercial Flagpoles
Browse FlagCo's commercial flagpole line: heights, pole types and wind ratings.
Flagpole Lighting
See FlagCo's flagpole beacon options for lighting your flag after dark.
Request an Install Quote
Tell Alabama Flag & Banner about your project. They'll follow up with a firm install quote, and walk the site first if the project calls for it.
Alabama Flag & Banner will follow up directly. FlagCo does not sell your information.
Ready to get your flagpole installed?
Call Alabama Flag & Banner at 256-534-1300, or request an install quote above.
